SAE |
 An Automated Model Based Design Flow for the Design of Robust FlexRay™ Networks |
2008-01-1031
By mandate of the Engineering Meetings Board, this paper has been approved for SAE publication upon
completion of a peer review process by a minimum of three (3) industry experts under the supervision of
the session organizer.
Thorsten Gerke
Synopsys GmbH
David Bollati
C&S Group/University of Applied Science Wolfenbüttel |
|
| Modeling and Simulating a VVT System for Robust Design |
2008-01-0901
By mandate of the Engineering Meetings Board, this paper has been approved for SAE publication upon
completion of a peer review process by a minimum of three (3) industry experts under the supervision of
the session organizer.
Jeremy Poole and Jim Patton
Synopsys, Inc.
Bill Goodwin
General Motors |
|
| Model Based Design of Robust Vehicle Power Networks |
2008-01-0898
By mandate of the Engineering Meetings Board, this paper has been approved for SAE publication upon
completion of a peer review process by a minimum of three (3) industry experts under the supervision of
the session organizer.
Thorsten Gerke
Synopsys GmbH
Alkiviadis Boulos
Jaguar Land Rover |
|
| Designing Automotive Subsystems Using Virtual Manufacturing and Distributed Computing |
2008-01-0288
By mandate of the Engineering Meetings Board, this paper has been approved for SAE publication upon
completion of a peer review process by a minimum of three (3) industry experts under the supervision of
the session organizer.
William Goodwin and Amar Bhatti
General Motors Corporation
Michael Jensen
Synopsys®, Inc. |
|
| Development of the Physical Layer and Signal Integrity Analysis of FlexRay™ Design Systems |
2007-01-1636
By mandate of the Engineering Meetings Board, this paper has been approved for SAE publication upon
completion of a peer review process by a minimum of three (3) industry experts under the supervision of
the session organizer.
Thorsten Gerke
Synopsys GmbH
David Bollati
C&S Group/University of Applied Science Wolfenbüttel |
|
| Robust Design of a Valve Train Cam Phasing Controller using Virtual Prototyping Techniques |
2007-01-1640
By mandate of the Engineering Meetings Board, this paper has been approved for SAE publication upon
completion of a peer review process by a minimum of three (3) industry experts under the supervision of
the session organizer.
Dale Witt
Createch Inc.
Bryan Kelly
Synopsys Inc. |
|
| Modeling and Simulation of Hybrid Electric Vehicle Power Systems |
2007-01-1592
By mandate of the Engineering Meetings Board, this paper has been approved for SAE publication upon
completion of a peer review process by a minimum of three (3) industry experts under the supervision of
the session organizer.
Min Zhang
Synopsys Inc |
|
| Electrothermal Behavior of a Complete Alternator Assembly within a Battery Charging System using Virtual Prototyping Techniques |
2007-01-1631
This paper illustrates the usage of virtual prototyping to observe the impact of self heating thermal effects on the performance of a complete claw pole alternator assembly.
Bryan Kelly - Synopsys Inc.
Voiko Loukanov - D&V Electronics Ltd.
V. Velikov - D&V Electronics Ltd.
J. Duliere - Synopsys Inc. |
|
| Modeling and Analysis of a Main Engine Start Power Flow |
2006-01-3046
The issues of power demand during a main engine start in an aerospace application are addressed. The effects of a resonance arising due to the presence of passive networks in the path of the power flow are modeled and analyzed, and recommendations are made for minimizing them.
Novica A. Losic - Honeywell |
|
| Virtual Embedded Mechatronics System |
2006-01-0861
In the past few years, the demands for more complex system development and the ever-increasing requirement for hardware and software improvements have increased the need for a virtual embedded system where the hardware, microcontroller and software coexist at the simulation level.
George Saikalis - Hitachi America, Ltd.
Hendrik Meyl - Hitachi America, Ltd.
Shigeru Oho - Hitachi America, Ltd.
Donald McCune - Hitachi America, Ltd.
Makoto Ishikawa - Hitachi America, Ltd. |
|
| Analysis of Vehicle Power Supply Systems Using System Simulation |
2006-01-0299
The Engineering Meetings Board has approved this paper for publication. It has successfully completed
SAE's peer review process under the supervision of the session organizer.
Thorsten Gerke
Synopsys GmbH
Carsten Petsch
Volkswagen AG |
|
| Development and Verification of In-Vehicle Networks in a Virtual Environment |
2005-01-1534
The Engineering Meetings Board has approved this paper for publication. It has successfully completed
SAE’s peer review process under the supervision of the session organizer.
Thorsten Gerke
Synopsys, Inc.
Carsten Schanze
Volkswagen AG |
|
|
| Saber-MATLAB Integrations: Enabling Virtual HW/SW Co-Verification |
The amount and complexity of embedded content in automotive systems is continually increasing. Driven
by pressures to increase content and reduce costs, automotive OEMs and suppliers are relying more on
embedded systems for control, configuration, and calibration of advanced technologies such as X-by-wire
systems, in-vehicle networking, and electric hybrid systems.
Lee Johnson—Synopsys |
|
| Modeling a Daytime Running Lamp Controller using StateAMS |
One of the greatest problems facing an engineer in order to use simulation as a design tool, is coming up
with suitable simulation models. Basic models are provided in the libraries of many simulation tools.
Nils Johnson—Synopsys |
|